Archive for the ‘Heat Pumps’ Category

« Older Entries

Germantown Heat Pump Question: Why Won’t My Heat Pump Start?

Thursday, March 29th, 2012

If you are having trouble with your Germantown heating system, or more specifically your heat pump, you may be surprised to learn that it is probably not the heat pump that is to blame.  That seems counterintuitive, but it’s true: the heat pump can be in perfect working order but still not turn on.

The good news, then, is that your heat pump is fine and you won’t have to pay an arm and a leg to fix or replace it. Still though, these types of problems can very frustrating to diagnose and correct. There are four common culprits when a heat pump won’t start.

  • A common problem is no power to your Germantown heat pump, which is certainly going to cause it to stop working. You should check your breaker box to make sure that the circuit breaker was not tripped. If your heat pump is wired to a switch, check to see if that switch is turned on. While this might seem obvious, its an important first step to take when troubleshooting.
  • Another quick check any homeowner can make is to see if the heat pump is set to the right mode. You want ‘heat’ mode on during the winter and ‘cool’ mode on for the summer. Again, this might seem obvious, but you should always check the mode before deciding that your heat pump needs a professional repair.
  • If you have recently replaced your home’s thermostat, it might not be communicating properly with your heat pump. Some thermostats don’t work well with heat pumps, so you should always check the model’s compatibility before installation. Incorrect wiring may also cause a problem. While you probably need a professional to fix this issue, it is relatively simple to resolve.
  • Germantown Heat Pump RepairThe last problem that commonly occurs is the heat pump’s own circuit breaker is tripped. Check your unit to see if your unit has its own circuit breaker to determine if that is the problem.

If you exhaust these problems and the problem persists or recurs – for example, if the circuit breaker trips again – call a Germantown heating and air conditioning contractor to work on your heat pump. There may be something larger at work that is causing problems in the electrical system that controls your heat pump, and that requires some expertise to properly address.

If you are having any problems with your heat pump, give Tuckers Air Conditioning & Heating a call today!

Photo by deejayres: http://www.flickr.com/photos/iamtheloop/242081320/sizes/n/in/photostream/

Tags: , , , ,
Posted in Heat Pumps | Comments Off

Gaithersburg Heat Pump Tip: Signs You Should Replace Your Heat Pump

Wednesday, March 21st, 2012

The decision to replace major equipment can be a difficult one. How do you know when to call it quits on a part of your Gaithersburg heating and cooling system that is as important as the heat pump?

Here are some signs that you should replace your heat pump:

  • If your Gaithersburg heat pump is making significantly more noise than it used to, it can be sign of major mechanical distress. Many times, replacement is the best solution.
  • Some components of a heat pump cost as much or more to repair as the whole unit does to replace. These components may include the compressor, the outdoor coil, the accumulator and the reversing valve. Once one of these goes, you are often better off replacing the heat pump than the broken component. Additionally, when repairs become so frequent as to no longer be cost effective, it’s a good time to replace the equipment.
  • A malfunctioning heat pump can cause problems with the humidity in your home. This is not a definitive indicator, but if you notice the humidity level rising in your home, you may need a heat pump replacement.
  • Any time your energy bill rises without a significant increase in usage, faulty or failing equipment is one of the top suspects. Your heat pump could very well be the culprit.
  • If you notice a cooling imbalance, such as rooms being too warm while others are too cool, your heat pump may be close to breaking.
  • Finally, if your heat pump is ten or more years old, replacing it is a good idea, even if it seems to be working fine. A new model will be much more efficient and chances are that the old one is headed for a major breakdown soon.

Keep in mind that these are not always definitive signs that your heat pump is done for good. Also, some of these may occur in combination. For example, you may have an old heat pump that is making a lot of noise and causing humidity problems.

Consult with Tuckers Air Conditioning & Heating for full diagnostics before making the decision to replace any major household equipment.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

Kensington Heat Pump Tips: What Happens When You Neglect Maintenance

Monday, February 27th, 2012

Just like any HVAC system, the heat pump in your Kensington home needs routine maintenance and yearly check-ups to operate as efficiently and safely as possible. You also don’t want your heat pump to wear down to the point of a major malfunction or breakdown, which can be costly to repair or may require a complete system replacement.

Here are some things that could go wrong and cost you a lot more in the end if you don’t keep up with the regular maintenance of your heat pump.

Damage to the Compressor

The compressor in a split-system heat pump works whether you are heating or cooling your home. In the winter, the compressor reverses the flow of the refrigerant to defrost the outdoor coils, and in the summer it supplies the refrigerant to cool the home, as well as cooling the outdoor coils. Proper airflow is vital to keeping the compressor running smoothly. Filters that are not changed regularly, dirty coils, and dirty fans can all restrict airflow, which will damage the compressor. Debris around the outside components should also be cleared to allow proper airflow.

Decreased Efficiency

When dirty or broken components restrict the airflow, this damages the compressor and decreases the heat pump’s efficiency levels.  Not only is it important to clean your heat pump regularly, but you should also have it checked by a certified heating technician once a year. This will also prevent safety hazards and other hidden issues with the heat pump.

Improper Refrigerant Levels

Most heat pumps are charged with refrigerant at the factory; however, if models that are charged when they are installed are not given the right amount of refrigerant this can also affect performance levels. Refrigerant leaks and other common problems can be prevented by scheduling an annual maintenance visit with one of our qualified Kensington technicians.

Don’t wait until the heat pump in your home stops working, call Tuckers Air Conditioning & Heating to schedule your yearly check-up.

 

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Common Aspen Hill Heat Pump Problems

Wednesday, December 28th, 2011

Heat pumps are great pieces of machinery to have in your Aspen Hill home, but they are not perfect. They come with their own problems and issues. Usually these can be fixed pretty easily, but it’s good to know what you are looking for.

Below are some common problems encountered by heat pump owners, along with some brief troubleshooting and repair advice. However, for any serious repair job, it is recommended that you call in a professional to fix the problem. This is to ensure the best performance of your heat pump, as well as for your own safety.

  1. No Heat – Obviously, this is a problem. A heat pump should do two things—heat and cool. If it’s not heating at all, something is wrong. Sometimes, this is just a matter of the power supply being interrupted. Press the “Reset” button on the power supply. If that does not fix it, it could be that the power supply has failed or the motor is overloaded.
  2. Incorrect Temperature – For example, you set the thermostat at 72 degrees, but even after several hours, the temperature won’t get over 70 degrees. This can be a problem with the sensor in the thermostat or with the heat pump itself. However, it could also just be the result of very cold temperatures outside. Heat pumps have trouble keeping up when the weather is consistently below 30 degrees Fahrenheit or so, so it may just need help in the form of a supplemental heat supply.
  3. It’s Noisy – Heat pumps are generally designed to run very quietly, so if you notice a lot of noise, there is probably something going on. Common culprits for this type of issue include loose connections, like screws, nuts and bolts. Check for any loose fittings on the heat pump. Also, make sure the contractor who does your annual heat pump inspection tightens these fittings as part of his maintenance routine.
  4. Frozen – This can be indicative of a few underlying problems, but the most common is dirt in the air filter. When filters get clogged, the heat pump can get frosted, ultimately leading to freezing. Check the air filter and make sure to change all air filters regularly.

Heat pumps can experience other issues, but these are some of the more common ones. Generally, though, heat pumps are pretty headache-free machines. Be sure to call a professional repair person if you experience any issues with your heat pump.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

What Size Heat Pump Is Right for My North Bethesda Home?

Monday, December 26th, 2011

One of the most important questions to answer when purchasing and installing any new heating or cooling system, no matter what type, is what size is best for your North Bethesda home. You need something that has enough capacity to heat or cool your whole home comfortably; otherwise your house will consistently be at an undesirable temperature.

Some people might think that the quickest solution to this problem is to just buy a system that they are sure has a capacity larger than the size of their home. You may even be tempted to get the biggest model out there, under the logic that the biggest is the best and it will be sure to be able to cover your whole house.

While this line of thinking might make sense to you, it’s actually not a good idea. The problem with this “solution” is that you can wind up with a heat pump that is considerably too large for your needs, which means your home will consistently be either too cool or too hot, and your energy bills will be unnecessarily high.

The best way to choose a new heat pump is to have a professional do a load calculation in your home. This can be a highly technical process, so it is best to leave it to the pros. However, here are some quick tips and other things to consider on the subject:

  • There are a lot of variable to consider in doing a calculation like this. A contractor doing a load calculation will consider the type of construction, what kind of insulation you have installed, what kind of windows you have, whether there is an attic, how many people live there and many more factors.
  • It never hurts to shop around. Get a few estimates from different area contractors, rather than just going with the first opinion.
  • Also, since heat pumps are used for both heating and cooling, different contractors may opt to do the calculation in different ways. Some will estimate capacity based on heating, while others will base it on cooling. Ask to see which is the case for each estimate you receive.
  • If you are getting a new heat pump as a replacement for an existing one, or even a different heating/cooling system, check the capacity of the unit you are replacing. That can be a good place to start. You will at least be in the right ballpark.

All of this means doing some extra leg work up front, but getting the proper sized heat pump is well worth the effort.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Chevy Chase Heating Tip: Heat Pump Load Calculation

Monday, December 12th, 2011

When purchasing a heat pump in Chevy Chase, the first thing you should do is determine what type of heat pump you want and how big it needs to be to provide ample heating and cooling to your home. If you’re unsure what you need, here are some tips to size a heat pump for your home’s particular needs.

The Importance of Sizing

Before buying anything, consider the cost of an oversized heat pump. A lot of homeowners opt for the biggest device on the market, but they don’t realize that they’re paying more than necessary for their device. An oversized device cycles on and off more often than is necessary and wears down much faster, resulting in an increased electric bill and faster wear on the device. It’s not good for your heat pump or your wallet.

How to Size

To correctly size a heat pump, the first step is to perform a load calculation. This is done by measuring the total volume of the rooms being heated (in cubic meters) and then determining the heating factor based on the type of insulation used.

There are different measurements depending on the type and R-rating of your insulation. For example, a single external wall without any additional insulation has a heating factor of 15. The number of external walls, the insulation in those walls and/or the ceiling and the rating of the insulation will determine the total heating factor for the room.

You will then divide the room volume by the heating factor to determine the number of KW (converted to BTUs) needed to heat that particular room.

Professional Sizing

The reason it is so important to call a professional heating contractor is that certain things, like poorly insulated windows, cracks in the foundation, leaks in the ducts and other issues can have an impact on the overall heating factor measurement. Additionally, the type of heat pump you choose must be effective when connected to an air handler for your entire home. A professional can make these measurements and ensure the right sized device is selected.

If you’re unsure about anything related to sizing and selecting a new heat pump for your home, call an HVAC in. They will perform a full load calculation and present your options for a new heat pump based on those calculations.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

My Boyds Home’s Heat Pump is Blowing Cold Air – What Should I Do?

Wednesday, December 7th, 2011

One of the most impressive things about a heat pump is that it can both cool and heat your Boyds home. But, if something goes wrong and your heat pump is suddenly trying to cool your home in the middle of the winter, you have a problem. Here are some possible causes of the issue and what you can do about them.

Defective Reversing Valve

The reversing valve is responsible for changing the flow of refrigerant between seasons so your heat pump can both heat and cool your home. So, if it breaks, you can imagine what happens next – you won’t switch into heating mode and your heat pump will try to air condition your home.

Defective reversing valves are hard to diagnose because the symptoms are largely the same as those of a defective compressor or condenser valve. However, because of how they are installed and where they are located, you will need an HVAC contractor to inspect this problem no matter what.

Low on Refrigerant

Your heat pump should never run low on refrigerant because it shouldn’t leak, but if it does and the refrigerant gets low or if your device is simply very old, this may be a problem. Low refrigerant means that the device cannot transfer enough heat between the outdoor air and the inside air and the air that gets blown through your ducts by the air handler isn’t heated as much as is necessary to warm your house.

The problem is relatively easy to fix, though you should also have your repairman check for leaks and a possible cause of the refrigerant being low in the first place.

Not Running at All

The final problem is one you should be able to notice quite easily. If the heat pump isn’t working at all but the air handler and blower are working fine, then the device will simply blow cold air from outside or possibly even just recycled cold air from inside. In either case, the heat pump isn’t running to heat the air and therefore, you’re getting whatever temperature it is outside.

This can be caused by a number of problems so it’s important to call for a professional to inspect it immediately.

Tags: , , ,
Posted in Heat Pumps | Comments Off

Guide from an Urbana HVAC Contractor: How to Maintain High Efficiency Heat Pump Filters

Monday, December 5th, 2011

The filter on your heat pump is an integral part of your Urbana home’s comfort system. Without that filter, the device will quickly be subjected to an influx of debris and contaminants that can get into the machinery and the air being filtered into your home. As a result, you need to make sure you properly maintain the filters to reduce stress on your heat pump.

Change Your Filters

High efficiency filters are designed to remove as much of the airborne contaminants in the air as possible. This is fantastic for keeping your indoor air clean. But if you don’t properly maintain the filter, air quality can worsen and your heat pump is put under unnecessary stress. Specifically, the extremely tight knit filter, designed to stop nearly anything from getting through, gets clogged.

Now your heat pump is forced to work much harder to draw the air it needs from outside and heat or cool your home. On top of that, the filter is filled with contaminants that can start to leak back into the air supply, actually making your indoor air quality worse than it would be otherwise. That’s why it is so important to clean your filters on a regular basis (for permanent filters) and replace them if they are one time use.

Recommended Filters

You have options as to which types of filters you use for your heat pump. Filters come in multiple options, from super high MERV rated filters that trap up to 99% of all contaminants as small as 0.3 microns.

Electrostatic filters are especially efficient because they extract contaminants of all types – from dust and mold to smoke and gas fumes. A good filtration system should effectively remove anything from the air without needing replacement too often.

Permanent filters tend to offer the best protection against airborne contaminants and generally need to be cleaned once a month. HEPA filters are often permanent and while each filter is different, these are often extremely effective at minimizing contaminants in the air without putting stress on your heat pump.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

Heat Pump Maintenance: A Guide From Ashton

Friday, October 7th, 2011

Heating and cooling your Ashton home is a priority. You need your home and family to be comfortable all year round, so you either got or are considering a heat pump. These machines are great because under the right circumstances, they are essentially all-inclusive and incredibly efficient solutions for all your home heating and cooling needs.

Notice the “under the right circumstances” part. A number of things have to be considered when choosing a heat pump, such as the climate and the size of your home. But these are not the only circumstances that influence how well your heat pump works for you. Proper maintenance is a vital component of heat pump ownership, ensuring that you get the best performance out of your heat pump for the longest time possible.

A major part of properly maintaining any machine is to keep it clean. A heat pump is no exception. Dirt and dust can affect the efficiency of your heat pump, as well as speed up corrosion problems. Keep the compressor and coils clean. Check them monthly or so and remove any accumulated dirt. Also, consistently check and change filters according to the manufacturer’s recommendations.

Simple cleaning is an easy and effective first step to heat pump maintenance, but there are some things that you just won’t be able to do on your own. For more intensive maintenance, it is best to call in a professional for an annual inspection.

During a routine maintenance check of your heat pump, a technician will inspect the whole heat pump system for problems. He will clean the compressor and coils, tighten any connections that may have loosened up and change the filters as needed. In addition, a skilled technician will be able to detect any early signs of trouble and make necessary repairs to prevent break downs. These small repairs can prevent big problems later on, thereby preventing some serious discomfort and a possible big expense.

If you are considering a heat pump as a heating and cooling solution for your home, great. If you have already decided on one and had it installed, congratulations on making a smart decision. Now, make another smart decision to protect that investment by keeping your new heat pump properly maintained.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

How Does a Heat Pump Work? A Question From Barnesville

Monday, October 3rd, 2011

If you’re in the market for a new home heating and cooling system in Barnesville, a heat pump is definitely an option worth considering. However, while the popularity of these systems is growing rapidly, many people still don’t understand what they’re all about. Before you go out and get yourself a new home comfort system, you should make sure you really know what you’re looking at

As their name suggests, heat pumps move heat from one location to another. However, their name can be misleading as well. Heat pumps are able to both heat your home in the winter and keep it cool in the summer by taking heat from the air in one place and sending it to another.

For example, your heat pump will remove the heat from your indoor air in the summer and pump it outside to keep your home cool. In the winter, the process is reversed, and the heat pump gathers heat from the outdoor air and pumps it inside to keep you house warm.

Of course, it’s not hard to see how the air inside your home in the summer has heat in it. But the outdoor air in the winter is cold. So how does a heat pump heat your house with cold air? Well, the truth is that there is almost always some heat in the air, no matter how cold it seems to you and me.

In fact, the temperature would have to drop well into the negative range before there was absolutely no heat to be found in the air. And heat pumps are specially designed to find that heat and collect it.

Basically all heat pumps work on this principle. However, they can’t keep your house comfortable all on their own. Heat pumps are usually installed as part of a complete home heating and cooling system. This means they’ll be paired with an air handler that can circulate the temperature controlled air throughout the house.

There are also some heat pumps that supplement the amount of heat they’re able to pull out of the air by heating it as it passes through. These types of heat pumps are often more effective in cooler areas, but because they require more energy to actually generate heat, they’re not typically as energy efficient as models that rely on their ability to get heat only out of the air.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

« Older Entries